에러 메세지 확인 좀 부탁드립니다.

요즘 서버가 자꾸 죽어서 dmesg 명령어로 확인을 해 본것입니다. 제가 보기에는 아무런 이상이 없는거 같은데...

고수님들 에러 메세지 확인 좀 부탁드리겠습니다. [root@goksc /root]# dmesg > error.txt
[root@goksc /root]# ls
backupdb/  db/  error.txt  mbox  q_start*  root/
[root@goksc /root]# cat error.txt
d is 133.2979 MHz.
Booting processor 0 eip 2000
Calibrating delay loop... 1861.22 BogoMIPS
Pentium-III serial number disabled.
OK.
CPU0: Intel Pentium III (Coppermine) stepping 06
Total of 2 processors activated (3722.44 BogoMIPS).
enabling symmetric IO mode... ...done.
ENABLING IO-APIC IRQs
init IO_APIC IRQs
 IO-APIC (apicid-pin) 4-0, 4-2, 4-9, 4-10, 4-11, 5-4, 5-5, 5-6, 5-7, 5-8, 5-9, 5-10, 5-11, 5-12, 5-13, 5-14, 5-15 not

connected.
...trying to set up timer as ExtINT... .. (found pin 0) ... works.
number of MP IRQ sources: 16.
number of IO-APIC #4 registers: 16.
number of IO-APIC #5 registers: 16.
testing the IO APIC.......................

IO APIC #4......
.... register #00: 04000000
.......    : physical APIC id: 04
.... register #01: 000F0011
.......     : max redirection entries: 000F
.......     : IO APIC version: 0011
.... register #02: 00000000
.......     : arbitration: 00
.... IRQ redirection table:
 NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
 00 003 03  0    0    0   0   0    0    7    51
 01 000 00  0    0    0   0   0    1    1    59
 02 000 00  1    0    0   0   0    0    0    00
 03 000 00  0    0    0   0   0    1    1    61
 04 000 00  0    0    0   0   0    1    1    69
 05 000 00  0    0    0   0   0    1    1    71
 06 000 00  0    0    0   0   0    1    1    79
 07 000 00  0    0    0   0   0    1    1    81
 08 000 00  0    0    0   0   0    1    1    89
 09 000 00  1    0    0   0   0    0    0    00
 0a 000 00  1    0    0   0   0    0    0    00
 0b 000 00  1    0    0   0   0    0    0    00
 0c 000 00  0    0    0   0   0    1    1    91
 0d 000 00  1    0    0   0   0    0    0    00
 0e 000 00  0    0    0   0   0    1    1    99
 0f 000 00  0    0    0   0   0    1    1    A1

IO APIC #5......
.... register #00: 05000000
.......    : physical APIC id: 05
.... register #01: 000F0011
.......     : max redirection entries: 000F
.......     : IO APIC version: 0011
.... register #02: 03000000
.......     : arbitration: 03
.... IRQ redirection table:
 NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
 00 0FF 0F  1    1    0   1   0    1    1    A9
 01 0FF 0F  1    1    0   1   0    1    1    B1
 02 0FF 0F  1    1    0   1   0    1    1    B9
 03 0FF 0F  1    1    0   1   0    1    1    C1
 04 000 00  1    0    0   0   0    0    0    00
 05 000 00  1    0    0   0   0    0    0    00
 06 000 00  1    0    0   0   0    0    0    00
 07 000 00  1    0    0   0   0    0    0    00
 08 000 00  1    0    0   0   0    0    0    00
 09 000 00  1    0    0   0   0    0    0    00
 0a 000 00  1    0    0   0   0    0    0    00
 0b 000 00  1    0    0   0   0    0    0    00
 0c 000 00  1    0    0   0   0    0    0    00
 0d 000 00  1    0    0   0   0    0    0    00
 0e 000 00  1    0    0   0   0    0    0    00
 0f 000 00  1    0    0   0   0    0    0    00
IRQ to pin mappings:
IRQ1 -> 1
IRQ3 -> 3
IRQ4 -> 4
IRQ5 -> 5
IRQ6 -> 6
IRQ7 -> 7
IRQ8 -> 8
IRQ12 -> 12
IRQ13 -> 13
IRQ14 -> 14
IRQ15 -> 15
IRQ16 -> 0
IRQ17 -> 1
IRQ18 -> 2
IRQ19 -> 3
.................................... done.
checking TSC synchronization across CPUs: passed.
PCI: PCI BIOS revision 2.10 entry at 0xfdb57
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: 00:00 [1166/0009]: Scanning peer host bridges
PCI: Scanning ServerWorks HE/LE Peer Bus Bridge 00/00
PCI: 00:01 [1166/0009]: Scanning peer host bridges
PCI: Scanning ServerWorks HE/LE Peer Bus Bridge 00/01
PCI->APIC IRQ transform: (B0,I2,P0) -> 19
PCI->APIC IRQ transform: (B0,I3,P0) -> 18
PCI->APIC IRQ transform: (B1,I4,P0) -> 16
PCI->APIC IRQ transform: (B1,I4,P1) -> 17
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 524288 bhash 65536)
Initializing RT netlink socket
Starting kswapd v 1.5
Detected PS/2 Mouse Port.
Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.13)
apm: disabled - APM is not SMP safe.
Real Time Clock Driver v1.09
RAM disk driver initialized:  16 RAM disks of 4096K size
PCI_IDE: unknown IDE controller on PCI bus 00 device 79, VID=1166, DID=0211
PCI_IDE: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x5440-0x5447, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0x5448-0x544f, BIOS settings: hdc:DMA, hdd:DMA
hda: SAMSUNG CD-ROM SC-152N, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12
raid5: measuring checksumming speed
raid5: MMX detected, trying high-speed MMX checksum routines
   pII_mmx   :  2092.452 MB/sec
   p5_mmx    :  2185.035 MB/sec
   8regs     :  1604.391 MB/sec
   32regs    :   942.594 MB/sec
using fastest function: p5_mmx (2185.035 MB/sec)
scsi : 0 hosts.
scsi : detected total.
md.c: sizeof(mdp_super_t) = 4096
Partition check:
RAMDISK: Compressed image found at block 0
autodetecting RAID arrays
autorun ...
... autorun DONE.
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
(scsi0) <Adaptec AIC-7899 Ultra 160/m SCSI host adapter> found at PCI 1/4/0
(scsi0) Wide Channel A, SCSI ID=7, 32/255 SCBs
(scsi0) Downloading sequencer code... 392 instructions downloaded
(scsi1) <Adaptec AIC-7899 Ultra 160/m SCSI host adapter> found at PCI 1/4/1
(scsi1) Wide Channel B, SCSI ID=7, 32/255 SCBs
(scsi1) Downloading sequencer code... 392 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.31/3.2.4
       <Adaptec AIC-7899 Ultra 160/m SCSI host adapter>
scsi1 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.31/3.2.4
       <Adaptec AIC-7899 Ultra 160/m SCSI host adapter>
scsi : 2 hosts.
(scsi0:0:0:0) Synchronous at 80.0 Mbyte/sec, offset 127.
  Vendor: QUANTUM   Model: ATLAS10K2-TY184J  Rev: DDD6
  Type:   Direct-Access                      ANSI SCSI revision: 03
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
(scsi0:0:1:0) Synchronous at 80.0 Mbyte/sec, offset 127.
  Vendor: QUANTUM   Model: ATLAS10K2-TY184J  Rev: DDD6
  Type:   Direct-Access                      ANSI SCSI revision: 03
Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
  Vendor: ESG-SHV   Model: SCA HSBP M14      Rev: 0.02
  Type:   Processor                          ANSI SCSI revision: 02
SCSI device sda: hdwr sector= 512 bytes. Sectors= 35860910 [17510 MB] [17.5 GB]
 sda: sda1 sda2 < sda5 sda6 sda7 sda8 >
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 35860910 [17510 MB] [17.5 GB]
 sdb: sdb1
autodetecting RAID arrays
autorun ...
... autorun DONE.
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 76k freed
Adding Swap: 1542200k swap-space (priority -1)
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/eepro100.html
eepro100.c: $Revision: 1.20.2.10 $ 2000/05/31 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and others
eth0: OEM i82557/i82558 10/100 Ethernet, 00:D0:B7:B6:C6:70, I/O at 0x5400, IRQ 18.
  Receiver lock-up bug exists -- enabling work-around.
  Board assembly 000000-000, Physical connectors present: RJ45
  Primary interface chip i82555 PHY #1.
  General self-test: passed.
  Serial sub-system self-test: passed.
  Internal registers self-test: passed.
  ROM checksum self-test: passed (0x04f4518b).
[root@goksc /root]#